Nippon Regio Formula Plus Driver Shafts Review

Nippon Regio Formula Plus Driver Shafts Review

By Russ Ryden, Fit2Score, A Dallas Fort Worth Club Fitter & Builder
The Highlands Performance Golf Center, Carrollton Texas 
Golf Digest Certified America’s 100 Best Club Fitter

It has been 9 years since I looked at the first generation Nippon Regio Driver shafts. That review included only one of the three models. In this review, all three models were measured and compared. While Nippon is well know for their iron shafts, the driver shafts in the US are not popular. That is an understatement, they are virtually unknown. Over the last several years a few of my long term affiliated trainers and players have raved about their experience with the Regio Formula Plus driver shafts.

If you do not follow my YouTube Channel, Devoted Golfer, this is Mark Pekarek discussing the N.S. Pro Regio Formula + driver shaft designs:

As with all Nippon golf shafts, the quality and consistency of the Regio Formula Plus Shafts are second to none. They are all made in Japan, expensive, and reflect the attention to quality that we expect from Japanese made products.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

Nippon Modus3 105 Review

Nippon Modus3 Tour 105

By Russ Ryden, Fit2Score, A Dallas Fort Worth Club Fitter & Club Maker
The Golf Center at the Highlands, Carrollton Texas

NipponM3T_105Image

The N.S Pro Modus3 Tour105 was released to the US public in August 2015. I had seen a set of these earlier in the year, labeled Prototype ST. The Modus3 Tour 105 is the same shaft that has been available on tour for several months. The word Prototype has been replaced with Modus3. I have been told it was put in play by a number of players. Lighter weight iron shafts are gaining broader acceptance in the tour community.

I am revisiting this review with a new look at the charts and numbers. As I prepared graphics for a speech to European club fitters I saw something in the charts that got my attention. A close look at the shafts confirmed what I saw in the graphics.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

Project X LZ Tour Graphite Iron Shaft Review

Project X LZ Tour Graphite Iron Shaft Review

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

ttpxlzgimage

The Project X Loading Zone steel shaft is getting a lot of tour play. Our tester with a 117 mph driver speed has made the Project X LZ 6.5 his gamer in his irons. Now the same brand name is on a 90 gram carbon fiber shaft for those of us with more modest swing speeds. I first noticed the shaft when my 2017 Mizuno fitting cart update arrived. This year’s 90g shaft from Mizuno is the Project X Tour LZ in a 5.0 and 6.0 flex.

What really got my attention was the FlexLoc torsional bands in the mid section of the shaft. These are the same bands used in the Project X LZ driver shafts. In the driver shaft, these band maintain stable torque and hoop strength through a section of the shaft with reduced wall thickness that created the soft midsection loading zone. 

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

---

ACCRA Concept Series 400 Driver Shaft Review

ACCRA Concept Series 400 Driver Shaft

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

accraconceptcs4image

The ACCRA Concept Series started in 2014 with the ACCRA Concept CS1 which is now called the Concept Series 300. The Concept CS1 was the first shaft I can recall from ACCRA  that was produced in a Japanese foundry. With it ACCRA shafts deliver the ultra premium shaft quality seen in high end Japanese golf shafts. The ACCRA Concept Series 400 is a variation of the Series 300 design aimed at reducing launch and spin.

This discussion of ACCRA shafts was shot at the 2016 PGA Merchandise show.

Lets take a look at the shaft measurements.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

---

True Temper Dynamic Gold X Seven Golf Shaft Review

True Temper Dynamic Gold X Seven

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

dg-x7-image

What new product can a company offer to strong golfers when they already have two of the most popular shafts in play on the PGA tour, the Dynamic Gold X100 and the Project X? We have seen the addition of the 7.0 flex of the Project X. That is a big number. How about hanging a Seven on the iconic Dynamic Gold brand. I see the Dynamic Gold X Seven profile as more like the Project X than a Dynamic Gold X100.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

---

Mitsubishi Diamana BF Golf Shaft Review

Mitsubishi Diamana BF-Series Fourth Generation Blue Board

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

mrc-diamana-bf-image

Mitsubishi has released the fourth generation of the classic Blue Profile. Like the third generation B, it is made using the proprietary high density Mitsubishi prepreg, Dialed and Mitsubishi MR70 fiber. The fiber is 20% stronger and 10% heavier than conventional prepreg. New is Boron Fiber is added to the tip section of the Diamana BF. One might assume that is what the BF indicates. What exactly can we see in the shaft measurements between the Third Generation B series and the BF.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

---