Fujikura Speeder Pro Driver Shaft Review

1 Reply

Fujikura Speeder Pro Driver Shaft

Russ Ryden, Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

SpeederProDriverRollingImageFujikura adds a Diver model to the Pro lineup, the Speeder Pro in 2015. I like the graphics on the Fujikura Pro Golf Shafts. The roll over from positive to negative on opposite sides of the shaft is great shaft art. The Pro line is available only through Fujikura charter dealers. This line of shafts is unique, within the line are 4 different profiles, each tuned to a particular swing type. That is an important aspect to understanding this shaft model.  Overlaying all the profiles is a confusing matrix. Sorting them as shown in the graphic below into their weigh groupings reveals the product strategy.

The technical discussion and measurements are available only to registered readers

The Speeder Pro uses high density material in the butt section to raise the balance of the shaft. That is seen in the positive numbers in the chart above. Balance numbers shown here are relative to the center of the shaft. A positive number is a balance toward the butt, a negative number toward the tip. These points are about as high I we see in current production. And as seen in the graphics and explained in the discussion with Alex, this was done without excessively stiffening the butt section of the tip. This was further aided by using high modulus material in the tip of the shaft. This created adequate tip stiffness without adding wall thickness and weight. All this speaks to the technology now being used in golf shafts.

Lets here what Alex Dee, from Fujikura has to say about these shafts. This is a segment of a 30 minute conversation about club fitting in general and about the 2015 Fujikura Shaft Models.

To see the entire discussion with Alex, click here.  Not shown in the numbers presented here. The Speeder Pro has a slightly larger butt than we typically see. These will make the grips a little larger. Something I find enhances the consistency of most golfers. Larger grips make it easier to hold on to the shaft.

If you are interested in this shaft, find a Fujikura charter dealer near you.

 

Oban ISAWA Golf Shaft Review

1 Reply

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

ObanISAWAImage

Oban ISAWA RED Driver Shaft

A box of the new Oban ISAWA shafts arrived and as I was preparing them for measurement I was wondering just where Oban would go with a new design. They already have 5 shafts in the premium Kiyoshi family covering a wide range of profiles . They have the the Devotion in the in the high mid price range and the Revenge in the lower mid price range. Just what was the ISAWA going to bring to the party. The first thing I noticed was the MSRP, $199. Putting it in the same price range as the Devotion and the Revenge. It is a different profile from all the other Oban shafts.

The technical discussion and measurements are available only to registered readers

This profile is a classic low launch design. I do not do comparisons between brands here. But, I know this profile. It is new for Oban, but it is not new in the business. This is a great addition to the design matrix offered by Oban fitters.

Aldila Rogue Golf Shaft Review – Driver

5 Replies

Aldila Rogue Driver Shafts

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

I first heard about the Rogue at the PGA Merchandise show in 2014. At that time is was a tour only shaft, made exclusively at Aldila’s California facility. Aldila has always had a huge presence on the PGA Tour. That presence became more visible when Jordan Spieth won the 2015 Masters with the Aldila Rogue in his bag. Lets start with a look at the numbers:

The technical discussion and measurements are available only to registered readers

- - -

 

Mitsubishi KuroKage XT Shaft Review

12 Replies

Mitsubishi KuroKage XT

By Russ Ryden, Fit2Score, A Dallas Fort Worth Club Fitter & Club Maker
The Golf Center at the Highlands, Carrollton Texas

KKXT_Image

The first version of this review was of a single shaft, others have arrived, prompting this update. There has been some buzz about the KuroKage XT. It quickly became popular on the PGA tour. Mitsubishi’s dealers have been snapping them up as soon as the shipments arrive.

TiNiThe KuroKage XT is another of the Mitsubishi shafts to incorporate highly elastic Titanium Nickel wire into the tip section of the shaft. The wire, shown here, is embedded into the prepreg and rolled into the tips section much like any other flag of prepreg would be.

In looking for a profile match, only Mitsubishi shafts were close. An interesting phenomena I never see. It hovers around the Diamana ‘ahina and the first generation Diamana white. The third generation Diamana White has moved on to a different design, which departs from the original profile. I see a variation on the ‘ahina. The flavor is there, the rough edges softened a bit, but if you were a fan of the original Diamana White Board or the second generation ‘ahina, you are going to like the KuroKage XT. The brittle hardness of the Diamana White and the ‘ahina have been softened by increasing the torque of the shafts. Yes, you heard that right, the overall GJ torque profile has been progressively increasing from the White to the ‘ahina and now to the KuroKage XT.

This video was shot at the 2015 PGA merchandise show. Meet Tsutomu Ibuki, the genius behind the Mitsubishi golf shafts. As we talk about this shaft late in the interview the feel of KuroKage XT design is discussed.

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

To continue reading this section of the review, you must be registered at a higher level membership.
Russ

Matrix Driver Shaft Review – REIGH & TIE Fitting System

Leave a reply

Matrix REIGH Driver Shaft &
Matrix White Tie, Red Tie, Black Tie Driver Fitting System

By Russ Ryden, A Golf Digest America’s 100 Best Clubfitter
Fit2Score, Dallas Fort Worth, Texas

MatrixReign_Image

The Matrix REIGN shaft is distributed exclusively through Matrix authorized club fitters. It is an elegant looking shaft with a laser etched logo and serial number. It comes in four structures, MCG, MTX1, MTX2 and HDZ. The MGC is the light weight game improvement design, mid to high ball flight and spin for lower swing speeds. MTX1 is slightly counter weighted for heavier heads or longer builds, the flighting and spin are mid range. The MTX2 series is traditionally weighted, and has a stiffer mid and tip section. The HDZ is premium Matrix, employing Boron and Zylon materials for feel and launch control. It is a unique profile emerging in a number of brands. A rapid loss of stiffness high in the shaft with a long stiff tip.

The technical discussion, measurements and testing results are available only to registered readers

The review samples are a subset of the REIGN line. But they are part of a new approach to golf club shaft fitting. Matrix created a 38 shaft system for Matrix Shaft fitters. They provide the fitting shafts and a software package to guide the fitter through the process of using their products of optimize launch and spin. I discussed this system with Tom DeShill, Director of R&D at Matrix Shafts during the 2015 PGA Merchandise show.

MatrixFittingGridThis fitting system also uses the Matrix Black, Red and White Tie shafts review earlier. The fitter finds the best fit in the Matrix Ozik Red Tie, then based on the optimizations target, continues testing with the proper weight and flex selected from the different design profiles to move the launch and spin toward the target.

My kit arrived and is being fitted with Club Conex UniFit tips. It will head to the range for fitting and testing, stay tuned.